Under the new European restrictions on formaldehyde emissions, motorhome manufacturers need to assess the technical documentation for the components used in their vehicles. But when a wood-based panel is processed, is the documentation for the original material still sufficient? Borri decided to investigate this question through independent testing of its own products, well before customers requested it.
Motorhome manufacturers know how much work goes into managing technical documentation. Each vehicle interior incorporates components from different suppliers, and when new regulatory requirements come into force, manufacturers need to establish what information is available and whether it is relevant to the products concerned.
The new European restrictions on formaldehyde emissions have brought one particular question into focus: does evidence of compliance for the original panel also demonstrate compliance for a component manufactured from it?
This matters to anyone sourcing bespoke wood components. Before a panel becomes part of a motorhome interior, it may be cut, routed, drilled, edged or laminated, and some of these processes can affect formaldehyde emissions. That, in turn, can affect how representative the original documentation is of the finished component.
Understanding the distinction helps manufacturers assess supplier documentation more accurately, without automatically accepting every certificate as sufficient or requesting additional testing when the existing evidence is already adequate.

Formaldehyde: What Has Changed Under the New EU Restrictions?
The restrictions introduced by EU Regulation 2023/1464, which amends Annex XVII of the REACH Regulation, have applied since 6 August 2026.
For furniture and wood-based articles covered by the restriction, the formaldehyde emission limit is 0.062 mg/m³, while a limit of 0.080 mg/m³ applies to other articles within its scope. Emissions must be assessed under the conditions specified in the regulation, which also provides for certain exemptions.
For motorhome manufacturers, these limits are among the requirements to consider when assessing product compliance. Suppliers are inevitably involved in the process, as manufacturers need documentation and information relating to the components used in their vehicle interiors.
In practice, however, documentation requests vary. Some manufacturers ask for declarations, others require test reports or additional material information, depending on their internal compliance procedures.
The challenge is to establish which evidence is genuinely relevant to the component being supplied. A document confirming the properties of a raw material does not necessarily provide all the information needed to assess a product manufactured from it.
The Panel Is Compliant, but What Happens During Processing?
Consider a panel supplied with documentation confirming its compliance with the applicable requirements. Once it reaches the factory, it undergoes the operations needed to produce the component specified by the customer: cutting, routing, drilling, edge banding and, depending on the design, the application of laminates, adhesives or finishes.
These are routine processes in wood component manufacturing, but they can affect the material’s emission characteristics.
Cutting and routing, for example, may expose internal surfaces through which formaldehyde can be released, whereas edge banding and surface coverings may restrict its release. Adhesives and finishes can also influence the outcome, depending on the materials and manufacturing processes involved.
This does not mean that every operation increases emissions. In some cases, the characteristics of the finished component can be adequately documented using data from the original panel, provided that the evidence is appropriate and representative of the product concerned.
In other cases, further assessment may be necessary because the material has undergone additional processing.
The regulation does not require every individual finished component to undergo new laboratory testing. It does, however, require compliance for articles within its scope to be supported by appropriate technical evidence, taking account of their characteristics and the applicable provisions.
It may be perfectly reasonable to conclude that a particular manufacturing process has no significant effect on emissions. The problem arises when that conclusion is simply assumed, without the technical evidence to support it.
For manufacturers purchasing processed components, the practical implication is clear: before accepting the documentation provided, they need to establish exactly which material or product it relates to and whether it adequately represents the processing carried out.
Borri’s Approach: Testing Before Being Asked
This was the starting point for us at Borri.
We manufacture bespoke wood components, including parts for the motorhome industry, using carefully selected, documented materials that we process to meet our customers’ specifications. We recognise the value of the documentation supplied with the original panels, but we also know that our manufacturing operations introduce further stages of processing.
With the introduction of the new formaldehyde requirements, we decided to investigate the emission characteristics of selected products after processing, rather than assume that the documentation for the materials we purchase would be sufficient in every case.
Before our customers requested any specific checks, we commissioned an independent research institute to test a selection of our processed products.
Our aim was to obtain results relating to the actual components examined, giving us technical information about the products and manufacturing processes covered by the tests.
Once we received the documentation, we shared it with all our customers rather than waiting for individual requests.
We were not seeking to demonstrate that every component manufactured by Borri had identical characteristics to the products tested. The results relate to the samples examined and cannot automatically be applied to every possible product configuration.
Our reasoning was straightforward: we would rather verify than assume, particularly when a manufacturing process may affect characteristics that cannot be assessed simply by looking at the finished product.
Within the industry, certain processes may be regarded as having no significant effect on emissions. That assessment may be correct, but it needs to be supported by relevant data or technical evidence.
For the products selected, we chose to investigate the matter through independent testing and make the results available to our customers.
Why We Shared the Documentation with All Our Customers
When a motorhome manufacturer gathers information about the components used in its vehicles, each supplier forms part of the compliance assessment process.
If the relevant technical documentation is already available, receiving it without having to request it individually allows the manufacturer to review it as part of its own procedures, establish which products it covers and assess whether it meets its specific needs.
That is why we decided to share the test results with all our customers.
We recognise that manufacturers may follow different procedures and require different documents. We also understand that results obtained from the products tested do not automatically replace the assessments needed for other configurations or intended uses.
What we can do is provide the information we have, clearly identify the components to which it relates and allow customers to assess its relevance.
For us, anticipating a technical request means addressing an issue before it becomes a problem that our customers need our help to resolve.
Borri has been working with wood since 1951, adapting over the years to manufacturers’ changing production requirements by supplying bespoke components made to their specifications.
Our approach to formaldehyde testing follows the same principle: understand the materials, assess the effects of manufacturing processes and document product characteristics where necessary.
For anyone purchasing processed wood components, there is a practical question worth asking when reviewing a certificate or test report: does the documentation cover only the original panel, or is the evidence also representative of the component that will actually be used?
That distinction can help manufacturers make more targeted requests to their suppliers and assess technical documentation with greater confidence.
To learn more about Borri’s manufacturing capabilities or request technical information about our components, get in touch.
Frequently Asked Questions
What formaldehyde emission limits does EU Regulation 2023/1464 introduce?
Since 6 August 2026, the regulation has set a formaldehyde emission limit of 0.062 mg/m³ for furniture and wood-based articles covered by the restriction, and 0.080 mg/m³ for other articles within its scope. Emissions must be assessed under the conditions specified in the regulation, which also provides for certain exemptions.
Does a panel certificate guarantee that a processed component is compliant?
Not automatically. Cutting, routing, edge banding, laminating and other manufacturing operations can affect a material’s emission characteristics. It is therefore necessary to assess whether the data available for the original panel is appropriate and representative of the component produced after processing.
Do manufacturing processes always increase formaldehyde emissions?
No. Their effects depend on the materials and processes used. Cutting and routing may increase the release of formaldehyde, while edge banding and surface coverings may restrict it. The outcome must therefore be assessed in relation to the characteristics of the product.
Is laboratory testing mandatory for every finished component?
The regulation does not require every individual unit produced to undergo laboratory testing. However, compliance for articles within its scope must be supported by appropriate technical evidence. Whether further testing or assessment is needed depends on the product’s characteristics, the data already available and the applicable regulatory provisions.
What testing has Borri carried out?
Borri commissioned an independent research institute to test a selection of its processed products, with the aim of obtaining data relating to the components examined. The resulting documentation was subsequently shared with all customers, before they requested it.